Guides

What Hemming, Tapering and Taking In Actually Cost

Alteration prices by operation, the 1.5 cm seam allowance most trousers carry, and the point where a cheap fix costs more than the garment.

Reviewed by Tessa Marlow · Updated Oct 16, 2026

The numbers first

  • Tailors price by the operation and the machine it needs, not by the price of the garment, so a $40 trouser and a $400 trouser often cost the same $20 to shorten.
  • A waist take-in runs into back pockets at about 5 cm.
  • A quote given with the garment in hand takes a minute and prevents the common surprise: a bill for two hems and a taper, with a waist taken in on top, running $130 on a pair of trousers that cost $90.
  • Most ready-to-wear trousers are sewn with about 1.5 cm of seam allowance at each side seam.

A hem is the cheapest alteration and the one most often paid for twice. Tailors price by the operation and the machine it needs, not by the price of the garment, so a $40 trouser and a $400 trouser often cost the same $20 to shorten. The corollary is worth internalising before any fitting-room decision: the alteration bill does not scale with the label, so a badly fitting expensive garment is not cheaper to fix than a badly fitting cheap one.

The price list, operation by operation

OperationTypical US priceTimeWhat limits it
Trouser hem, straight$15–301 dayOriginal hem finish
Jean hem, chain stitch$20–352–3 daysChain-stitch machine
Leg taper$30–602–3 daysPocket and selvedge
Waist taken in$40–803–5 daysPocket position
Sleeve shortened, cuffed$35–653–5 daysButton placement
Jacket relined$150–3001–2 weeksLining yardage

Rates vary by city and by whether the shop keeps a dedicated chain-stitch machine for denim. A chain stitch stretches with the fabric and fades like the original; a lock stitch does neither. That is most of the price gap.

Hands guiding fabric through a white sewing machine in a bright workroom
Hands guiding fabric through a white sewing machine in a bright workroom

Each “what limits it” is worth reading as a veto. A taper that has to navigate a pocket bag can only narrow the leg below the pocket opening; above it, the tailor is sewing through the pocket itself. A waist take-in runs into back pockets at about 5 cm. A cuffed sleeve shortened from the cuff end disturbs the buttonhole. When a shop quotes fast and cheap on an operation whose limiter applies to your garment, the quote is the thing to distrust.

How quotes go wrong

Ask for the price before the pinning, not after. A quote given with the garment in hand takes a minute and prevents the common surprise: a bill for two hems and a taper, with a waist taken in on top, running $130 on a pair of trousers that cost $90.

The pattern behind the surprise is per-operation pricing meeting multi-operation work. Each operation looks small in isolation, and a stack of them does not feel like a total until it is one. Reputable shops quote the stack; the ones that quote per operation after the fitting bank on sunk-cost psychology at the counter. There is also a legitimate version of the surprise: once the tailor opens a seam, hidden problems — a lined waistband, selvedge seams, a factory finish that cannot be replicated — can raise the job’s real difficulty. The difference is that the honest shop comes back with a number before continuing.

The 1.5 cm seam allowance rule

Most ready-to-wear trousers are sewn with about 1.5 cm of seam allowance at each side seam. That gives roughly 3 cm of total room to let out at the waist, and often less at the seat because the allowance tapers toward the crotch. Check inside the waistband before buying a pair that is close but not right.

Taking in has a firmer ceiling. Up to 5 cm the alteration hides in the side seams and the back seam. Past that, the back pockets drift toward the hips and the curve of the seat changes.

A tailor can do it. You will see it.

Letting out is a loan, not a reserve

The 3 cm of seam allowance reads like free room, but it is a one-time resource. Once a seam is let out, the allowance is consumed: the fold has been pressed flat and trimmed if the tailor needed a clean finish. A garment let out once has nothing left to give a second time, and the fabric at the old fold line often shows a pressed crease that pressing again will not fully erase.

Letting out also costs more than taking in per centimetre gained, because the seam has to be opened, pressed flat, re-sewn along a new line and re-finished where the old stitch holes show. Compare that against the price table and the arithmetic is clear: a waist taken in at $40–80 is the common job, while a waist let out is the job tailors accept reluctantly and price accordingly. Buy for the larger measurement and take in; the industry is built around that direction for a reason.

Length is decided by the shoe

Hem the trouser with the shoes you will wear. A full break needs about 2 cm of extra length over the shoe; a half break, 1 cm; no break sits at the top of the sole. The same trouser can need three different hems for three pairs of shoes, which is why inseam measurements taken without shoes are only a starting point.

The break is the fold of fabric where the trouser rests on the shoe, and it is a style decision with a mechanical cost. More break means more fabric pooling, which wears at the fold and looks loose; no break shows sock when sitting and looks intentional but unforgiving on height. Because the hem cannot be un-cut, this is the one alteration where the direction of error matters most: hem too long and a second pass fixes it, hem too short and the fabric is gone.

Sleeves: from the cuff, not the shoulder

For a jacket, sleeve length is measured at the wrist bone with the arm slightly bent. Shortening from the cuff end means moving buttons and the buttonhole, and that is where the $35 becomes $65. Shortening from the shoulder end is a bigger job and rarely worth it on a fused jacket.

Working from the shoulder end detaches the sleeve from the armscye, which means re-setting the whole sleeve head — skilled handwork, priced to match, and on a fused jacket the canvas rarely survives the operation cleanly. Cuff-end work has its own floor: functioning surgeon’s cuffs with a real buttonhole cannot be shortened from below without closing the cuff, so those jackets force the shoulder route whether or not it is wise. Check which cuff you have before buying a jacket that needs half an inch off.

When the alteration costs more than the garment

A jacket reline runs $150 to $300, which is reasonable on a wool coat and absurd on a $120 blazer. The same logic applies to a lining that has failed at the underarm: the fix is a panel, not a full reline, and a good tailor will say so. Lining failure explains where those tears start.

Two more ceilings worth knowing. A shoulder can move about 1.5 cm before the sleeve head comes off. A waist can come in 5 cm before the pockets betray it. Past either line, the honest answer is a different size, not a bigger bill. Spec sheets give you the numbers to check before you buy.

The habit this section rewards is dividing the garment’s price by its remaining alteration ceiling. A coat worth relining has years of service behind the $200; a blazer priced near the relining cost is finished the day its lining wears through. Size is the same calculation run in advance. Every centimetre outside the 5 cm waist ceiling converts directly into tailoring dollars, and the size chart on the product page costs nothing to read.

More in Buying Guides

FAQ

How much should a trouser hem cost?
Expect 15 to 30 US dollars at a dry cleaner or neighborhood tailor, and 25 to 40 at a shop that keeps the original hem finish. A blind hem costs more than a straight stitch because it is sewn by hand or on a dedicated machine.
Can a waist be taken in more than 5 cm?
It can be done, but not invisibly. Beyond about 5 cm the back pockets move toward the side seam and the seat flattens. Beyond 8 cm the side seams no longer sit where the pattern intended.
Is letting out a garment cheaper than taking it in?
Usually yes, when there is seam allowance to release. Most mass-market trousers carry 1.5 cm per side, so roughly 3 cm total at the waist. A garment already let out once has nothing left.

Second Look

Every figure used above, with the section it appears in. If a number here does not match the page you are reading, trust the page — and tell us.

$
Introduction
1 day
The price list, operation by operation
3 days
The price list, operation by operation
5 days
The price list, operation by operation
2 weeks
The price list, operation by operation
5 cm
The price list, operation by operation
1.5 cm
The 1.5 cm seam allowance rule
3 cm
The 1.5 cm seam allowance rule

Tessa Marlow

Writes about garment construction, leather goods and footwear specs. Started in retail floor management before moving to editorial research. Our standards.